Jump to content

Formula One car

From Wikipedia, the free encyclopedia
For a summary of the technical and sporting regulations of Formula One racing, see Formula One regulations.

This article is part of a series on
Formula One
Previous and next seasons
Related articles
Lists
Records
Organisations

A Formula One car or F1 car is a single-seat, open-cockpit, open-wheel formula racing car used to compete in Formula One racing events. It has substantial front and rear wings, large wheels, and a turbocharged engine positioned behind the driver. The cars are constructed of carbon fibre and other composite materials for durability and are built to withstand high impact forces and considerable g forces.

The early F1 cars were simpler designs with no wings, front mounted engines, and required significant driver effort to control. Later improvements saw the introduction of lighter cars due to metallurgical advancements, introduction of ground effect cars with the addition of wings and other aerodynamic surfaces, and control electronics. The introduction of turbocharged engines with higher efficiency, and energy recovery system to boost speeds led to faster and efficient racing cars.

A modern F1 car has a carbon fibre monocoque with a open cockpit consisting of a single driver seat and detachable steering. The 1.6 L V6 engine is capable of producing up to 950 hp (710 kW), which enables the car to reach speeds of up to 375 km/h (233 mph). It uses semi-automatic gear boxes with a seven speed transmission and a electronic-hydraulic control to drive the car. The 18 inch wheels are fitted with slick tyres during normal dry conditions, and are fitted with carbon disc brakes capable of handling temperatures of up to 1,000 °C (1,830 °F). The wings act as inverted aerofoils to produce negative lift, resulting in increased down force.

The regulations governing the cars are specified by the FIA and have undergone considerable changes since their introduction in the late 1940s. The cars are constructed and operated by the constructors in racing events, though the design and manufacture can be outsourced. Since the 2000s, several changes have been made by the FIA, which are aimed at sustainability and cost reduction, such as the cap on car parts, usage of mixed fuel, and usage of energy recovery systems. It has also sought to reduce the downforce and limit speeds, while simplifying car design and improve close racing. Cars have also been made safer with durable materials, improvement in safety features and addition of halo.

History

[edit]
Further information: Formula One regulations
Early F1 cars were simpler with no wings and front mounted engines.

The early F1 cars were simpler designs with no wings, front mounted engines, and required significant driver effort to control. In the early 1960s, lighter cars with aluminum chassis were introduced with the addition of wings towards the end of the same decade. In the 1970s, understanding of aerodynamics began to impact the car designs singnificantly, with the introduction of nose boxes in the front, and air boxes behind the driver to increase air flow to the engine. The advent of ground effect cars in the 1980s, allowed to increase downforce with a small drag penalty. With continuous improvement in engines and the introduction of turbochargers, cars produced an increased amount of thrust.[1] The maximum permitted width of the cars was 2,150 mm (85 in) with a 1,500 mm (59 in) front axle and 1,000 mm (39 in) wide rear axle, and the maximum width was reduced to 2,000 mm (79 in) in 1994.[2]

Following the 1994 San Marino Grand Prix, a number of changes were introduced, which led to the development of modern day F1 cars. A 10 mm (0.39 in) thick wooden skid block was added on the underbody to enforce minimum ground clearance. In the following seasons, several modifications were introduced, the underbody plank was lengthened and a 50 mm (2.0 in) tall, 500 mm (20 in) wide block was added on top of the plank to minimize the ground effect. The front wing height was increased from 40 to 50 mm (1.6 to 2.0 in) and the maximum height was reduced to 200 mm (7.9 in) above the reference plane. A step wise design was introduced with reduced side pods, and engine cowling, and exclusion zones were added around the wheels to prevent any bodywork in the area apart from the suspension.[2]

The structure of modern F1 cars developed in the 1990s.

Since the 1990s, improved electronics were incorporated to increase the efficiency, handling and reliability of the cars. Since the 2000s, with computer aided design, teams have been able to produce more efficient cars, with several changes aimed at sustainability and cost reduction, such as the cap on car parts, usage of mixed fuel, and usage of energy recovery systems.[1] In the 2000s, the front height was increased progressively to 150 mm (5.9 in) and the maximum width and height were defined as 500 mm (20 in) and 950 mm (37 in) respectively. FIA enacted further changes to the body structure over the subsequent years such to improve racing changes to the structure and height of the front wing, and changes to floor design. The governing body outlawed several structures introduced by the teams, including double diffusers, modified exhaust ducts, and extra aerodynamic elements such as sharklets, cooling slots, winglets and dive planes. Modifiable front wings were also trailed in 2009 and the Drag reduction system (DRS) was introduced in 2011. The latest rules in the late 2010s introduced simpler front wings, which reduced the dirty air from the cars, and enabled more closer racing.[2] The underside of the vehicle must be flat between the axles with the wear of skid block limited to a maximum of 1 mm (0.039 in) during the race.[3] The latest regulations which came into effect in 2022 with the intention of enabling more closer racing, simplified the aerodynamic components, which reduced vortices, and created more ground effect.[4][5]

Design

[edit]
Modern F1 cars feature elaborate aerodynamic elements.

The modern Forumula One car is a single-seat, open-cockpit, open-wheel racing car with substantial front and rear wings, large wheels, and a turbocharged engine positioned behind the driver. The monocoque is constructed of reinforced carbon fibre, lined with kevlar and fire resistant materials to protect the drivers from high impact crashes and fires. The driver cockpit consists of single seat with a detachable steering wheel in the front. There is a halo mounted on top of the open cockpit, which was introduced in 2018. Two front and rear wheels are bolted to the suspension and the engine is mounted behind the driver. The front and rear wings are aerodynamic surfaces fitted on the extremes.[6] The minimum weight permissible is 798 kg (1,759 lb) including the driver, while fitted with dry-weather tyres and no fuel.[7][8] The cars are limited to dimensions of 5.63 m (18.5 ft) in length, 2 m (6 ft 7 in) in width, and 0.9 m (2 ft 11 in) in height.[9]

Components

[edit]

Engine and fuel

[edit]
Main article: Formula One engines
A Cosworth DFV V8 engine fitted to a Tyrrell, used from the late 1960s to early 1980s.

Since its inception, Formula One has used a number of different engine regulations.[10][11] During the early years, a front-engine, four-wheel-drive layout was used with a 4.5 L naturally aspirated or a 1.5 L supercharged engine capable of an output power of up to 317 kW (425 hp). Progressively the engine capacity and power were reduced, and was limited to 0.75 L with compressor or 2.5 L without one during the late 1950s. In 1961, the engine was positioned behind the driver and the capacity was regulated to 1300–1500 cc with a power output of 150–225 hp without supercharging. In 1966, FIA increased engine capacity and allowed up to 3.0 L atmospheric with a power range of 290–370 kW (390–500 hp) or 1.5 L supercharged with a power range of 370–670 kW (500–900 hp). While the basic structure and configuration of a Formula One remained same since the late 1960s, the power output of the engines increased progressively to 1,000 kW (1,400 hp) at 12000 rpm in 1986. In 1987-88, turbocharged eight-cylinder engines were introduced alongisde atmospheric engines with fuel caps for races introduced for turbocharged engines. Turbocharges were banned from 1989 with 3.0 L engines becoming the norm in the 1990s and led to the introduction of V10 and V12 engines.[11][12]

A four-cylinder 1.5 L turbo BMW engine from the 1980s.

The teams started constructing engine components using advanced metal alloys such as titanium and beryllium, which reduced weight and improved the efficiency and durability. FIA outlawed the use of these towards the late 1990s with only iron and aluminum permitted. The introduction of pneumatic valve springs in the same period allowed the engines to reach up to 20,000 rpm.[12] For a decade, the F1 cars had run with 3.0 L naturally aspirated V10 engines producing 730–750 kW (980–1,000 hp) of power with top speeds of upto 375 km/h (233 mph).[13] Though the FIA continually enforced material and design restrictions to limit power, the V10s in the 2005 season were reported to develop 730 kW (980 hp), power levels not seen since the ban on turbocharged engines in 1989. Before the 2006 season, FIA introduced a new engine formula, which mandated cars to be powered by 2.4 liter naturally aspirated V8 engine configuration, with no more than four valves per cylinder and banned variable intake trumpets. For the 2009 season, the engines were limited to 18,000 rpm to improve engine reliability and cut costs.[11][14] In 2012, the engines consumed around 450 L (16 cu ft) of air per second with a race fuel consumption rate of 75 L/100 km (3.8 mpg‑imp; 3.1 mpg‑US).[15]

Crash resistant fuel bladders, reinforced with kevlar are used.

For the 2014 season, FIA introduced 1.6 L six-cylinder turbocharged engines with an kinetic energy recovery system (KERS) to increase fuel-efficiency.[11][16] For 2022, a modified V6 configuration was introuced with a more powerful KERS.[17] Over the years, FIA has been gradually reducing the overall allocation of engines per season and with the increasing number of races, each engine is expected to last for at least 2,000 km (1,200 mi). FIA had also introduced standardization of certain engine parts and cap on engine components to reduce costs with grid penalties applied for drivers who exceed the allocation.[11] As per the current regulations, a maximum of five power units are allowed per season.[18] The engine is located between the driver and the rear axle and is bolted to the cockpit at the front end, and transmission and rear suspension at the back end.[12]

The fuel used in F1 cars is a mixture of unleaded petrol and ethanol with a tightly controlled mixture ratio. As a part of the regulation change in 2022, the ethanol content was increased from 5.75% to 10%.[19][20] Cars were allowed to be refuelled during the race till 2010, after which refueling was banned. The cars are stipulated to carry a maximum fuel of 110 kg per race, with at least 1 kg to be made avilable to the FIA for post race inspection. Any abnormalties in the fuel or failure to provide the sample results in disqualification from the race.[21] The fuel bladder is made of high quality rubber lined with kevlar for protection against crashes and is located in front of the engine, behind the cockpit.[22][23]

Steering and transmission

[edit]
A typical electronic steering wheel used in a F1 car.

A typical steering wheel used in a F1 car is an electronic control with an array of knobs, buttons and levers. It is made of carbon fibre with titanium, silicon, fibreglass, and copper parts. It has two driver handles on the sides with a LCD display in the center, LED gear shift lights at the top and gear shift paddles in the back. The steering wheel is used to control various functions of the car such as gears, engine revolutions, fuel–air mix, brake balance, differential mapping, among others. The display displays various data points including engine parameters, gears, temperature and time. The steering wheel is also used to access the radio and control the drinking mechanism.[24][25] It weighs about 1.3 kg (2.9 lb) and can cost about $50,000.[26]

The gearbox and rear suspension from a Lotus T127 in 2010 season.

While conventional manual gearboxes were used earlier,[27] modern Formula One cars use semi-automatic sequential gearboxes with a rear-wheel-drive. It has eight forward gears and a reverse gear operated with paddle-shifters.[28][29] The gearbox is constructed of carbon reinforced titanium, and is bolted onto the back of the engine.[30] Fully-automatic gearboxes, and systems such as launch control and traction control were banned in the 2000s to keep driver skill and involvement important in controlling the car, and reduce costs.[31][32] When the driver initiates gear shifts using paddles mounted on the back of the steering wheel, a system of solenoids, hydraulic actuators, and sensors perform the actual shift, and electronic throttle control. Clutch control is also performed in the same manner except when launching from neutral into first gear, where the driver operates the clutch manually using a lever on the back of the steering wheel.[33] The clutch is a multi-plate carbon design with a diameter of less than 100 mm (3.9 in), and weight of less than 1 kg (2.2 lb), capable of handling up to 540 kW (720 hp).[34] The cars use seamless shift transmissions, which allow almost instantaneous changing of gears with minimum loss of drive and a shift times of 2–3 ms.[35] As a measure to reduce costs, gearbox ratios are fixed for a season and a team is allowed a maximum of four gearboxes per season.[36][37]

Wheels and tyres

[edit]
Main article: Formula One tyres
Grooved tyres were used between 1999 and 2008.

During the 1950s and 1960s, Formula One tyres were treaded rubber tyres similar to the automobile tyres but larger.[38] In late 1950s, cotton fabric was replaced with nylon fabric, which reduced weight and increased durability. In the 1960s, the tyres became wider and synthetic rubber was used along with nylon.[39] Slick tyres were introduced for the first time during the 1971 season.[40] In the 1975 season, the cars used 26.0"×16.2"–13" slick tyre (diameter × width) in the rear on a 13"×18" rim, and a 20.0"×9.2"–13" slick tyre in the front on a 13×10" rim.[41] For the 1981 season, the maximum diameter of the rear tyre was limited to 26.0", and the diameter of the front tyres was increased, with the tyres measuring 25.0"×10.0"–13" in the front and 26.0"×15.0"–13" in the rear.[42] Ahead of the 1993 season, the width of the rear was reduced from 18" to 15".[43] In 1998, grooved tyres were introduced with three groove lines in the front tyres and four groove lines in the rear tyres.[44] Between 1999 and 2008, regulations required the tyres to feature a minimum of four 14 mm (0.55 in) grooves in them, with the intention of slowing the cars down as the slick tyre, with no indentations, provides the most grip in dry conditions.[45][46] The tyre sizes were limited to 355 mm (14.0 in) at the front and 380 mm (15 in) at the rear, and the maximum diameter was 660 mm (26 in) for dry and 670 mm (26 in) for wet tyres.[47] Briefly in 2005, tyre changes during the race were outlawed and the tyre compounds were made harder to last the full race distance.[48]

Various compounds of colour coded slick tyres are used during dry weather.

Slick tyres were reintroduced at the beginning of 2009, with the front tyres narrowed from 270 mm (11 in) to 245 mm (9.6 in), to shift the balance towards mechanical grip in an attempt to increase overtaking.[38][49] Since the introduction of slick tyres in 2009, the tyre construct has remained almost the same with only variations to tyre sizes.[38] The teams are given a fixed number of sets of three compounds of slick dry weather tyres, and additional sets of grooved intermediate and wet weather tyres for a race weekend. The tyre compounds are demarcated by a colour coding, with the teams mandated to use at least two dry compounds during a dry race.[50][51][52] Briefly in 2016, teams were given an option to choose tyre compounds.[53][54] For the 2017 F1 season, significantly wider Pirelli tyres were introduced at both the front and rear axles, while the overall diameter of the tyres was increased from 660 to 670 mm (26 to 26 in). Front tyre size increased to 305/670-R13 while rear-tyre size increased to 405/670-R13.[55] For the 2022 F1 season, the wheel rim diameter size was increased from 13 to 18 in (330 to 460 mm), and the diameter was increased from 670 to 720 mm (26 to 28 in).[38]

A brake disc on a F1 car.

Disc brakes are used for breaking, similar to road cars. The brakes consist of a rotor disc and a caliper, with six piston clamp pads inside each caliper. The driver applies pressure on the brake pedal, which uses hydraulic pressure to drive the clamps and the friction on the disc slows the car. The front brakes are simpler with direct pressure applied onto the breaking discs to slow down. In the rear, breaking is achieved by the combination of three forces, friction on the breaks, resistance from the engine, and the energy recovery system. The driver can control the effect of these and break distribution using the steering wheel.[56] An average F1 car can decelerate from 100 to 0 km/h (62 to 0 mph) in less than 15 m (49 ft) and hence the breaks are subjected to high temperatures of up to 1,000 °C (1,830 °F) and severe g forces.[57] To withstand high temperatures, breaks are made of carbon composites. The breaks are cooled by air passing through numerous small holes in the break ducts.[56]

Wings

[edit]
A typical front wing of a F1 car in the 2000s.

Early designs linked wings directly to the suspension, but several accidents led to rules stating that wings must be fixed rigidly to the chassis.[1] The wings are aerofoils on the front and rear of the car, and are made of carbon fibre composites for higher strength and reduced weight. The front wing is a forked structure with a maximum width of 1,800 mm (71 in) and must not extend more than 200 mm (7.9 in) beyond the center line. It can have a maximum of four wing elements and should not bend more than 5 mm (0.20 in). It is made of aluminium alloy, carbon fibre and fibre glass, and can cost up to $300,000.[58] The rear wing consists of a main plane which spans the width of the car with smaller horizontal flaps that angle downwards. There are short upright tabs on the trailing edge of the flaps with vertical end plates at the wing tips. The DRS is a flap adjustment mechanism in the rear wings that is operated hydraulically following steering inputs from the driver.[59]

Energy recovery system

[edit]
Operation of KERS in a F1 car.

The kinetic energy recovery systems (KERS) recovers the kinetic energy created by the car's braking process. It stores that energy and converts it into power that can be used to boost acceleration. There are principally two types of systems: electrical and mechanical flywheel. Electrical systems use a motor-generator incorporated in the car's transmission which converts mechanical energy into electrical energy and vice versa. Once the energy has been harnessed, it is stored in a battery and released at will. Mechanical systems capture braking energy and use it to turn a small flywheel which can spin at high speeds. When extra power is required, the flywheel is connected to the car's rear wheels.[60] KERS typically adds 120 hp (89 kW) additional power boost for a specific time.[61]

Other elements

[edit]

A nose box or nose cone is a structure to which the front wing is attached. It directs the airflow towards the floor of the car, and acts as a shock absorber in case of accidents. It is made of high strength composite materials and is subjected to various load tests by the FIA to ensure its rigidity.[62] The halo is a safety device mounted on the cockpit, and is made of series of curved metal bars intended to protect the driver's head during crashes.[63] The air box is situated behind the cockpit, and serves as the receptacle of the high speed air moving over the body. It supplies the pressurized air to the engine intakes, boosting its power and absorbs the turbulence generated from the air passing over the driver's helmet. Air filters are used to filter the dirty air before being passed into the engines.[64]

Aerodynamics

[edit]

Aerodynamics has become key to success in the sport, and the teams spend time and money on research and development of the same each year.[1] The sculpted front and rear wings with the rest of the body parts such as the vanes beneath the nose, bargeboards, sidepods, underbody, and the rear diffuser, play a role in determining the aerodynamic efficiency of the car. A modern Formula One car capable of developing up to six G of lateral cornering force and a downforce equivalent to twice its weight at 190 km/h (120 mph).[65][66] The car is designed to create the maximum amount of downforce for the minimal amount of drag with the configuration often modified to the requirements of a particular track.[58] The interaction of various components amplify the total downforce more than the sum of their standalone contributions.[59]

Front of a F1 car showing the front wing arrangement.

The wings operate similarly to inverted airplane wings, to produce a negative lift or downward force. The profile of the front wing, along with the angle of attack against the incoming air, define the downforce generated. Other smaller elements such as flaps, and gaps between the elements help with controlling the airflow. A steeper angle of attack increases the downforce while creating increased drag. The front wing also directs the airflow to the rest of the car with the air flowing into the sidepod intakes used for the temperature regulation of the engine. The air flowing underneath the floor helps to seal the gap with the ground, contributing to the ground effect. A low-pressure area is created which effectively sucks the car towards the ground, increasing the down force and grip of the car. The designers aspire for a smoother airflow over the body of the car, while minimizing the wakes formed by the rotating wheels.Vortices created between the front wing and the nose box help to reduce the turbulence. Minor changes to the front wing can have drastic effects on the aerodynamics of the car.[58]

Rear of a F1 car, showing the rear wing and diffuser configuration.

The rear wings serve similarly to the front wings as inverted airfoils, and deflect the air downwards, causing a down force. The angle of the main plane and flaps determine the direction of the airflow, with other elements used to further fine tune the same. Higher angles increase downforce while also contributing to a higher turbulence and decreased stability of the rear wing. The rear wings are designed so as to withstand high loads without decreasing the downforce. The other structural elements of the car such as the side pods, and body work determine the amount of air flowing through the rear wings. The rear wing generates vortexes which keep the airflow attached to the car longer, delaying the aerodynamic stall. The rear wing can be modified to various configurations depending on the race track and the circumstances.[59] The DRS opens a slot in the rear wing at the behest of the driver. It reduces drag and increases power, and hence speed, and is allowed to operated in specific instances.[67] The diffuser located at the rear is used to combine the pressurized airflow from the underside of the car to create more downforce.[58]

Performance

[edit]
The BAR-Honda 007 set an unofficial speed record of 413 km/h (257 mph) at Bonneville Speedway.

The 1.6 L V6 engine on a modern F1 car churn out 710 kW (950 bhp) at 15,000 rpm.[68][69] This enables a modern F1 car to accelerate from 0 to 60 km/h (0 to 37 mph) in 1.8 seconds, and from 0 to 100 km/h (0 to 62 mph) in 2.6 seconds.[70] It has a power-to-weight ratio of 1,297 hp/t, which would theoretically allow the car to reach 100 km/h (62 mph) in less than a second.[71] However, due to traction loss, it accelerates slower and when the traction loss is minimal at higher speeds, the car accelerates at a very high rate.[72] A F1 car is also capable of rapid deceleration and cornering at high speeds. Due to rapid acceleration and deceleration, the drivers may experience high levels of g force. The drivers experience 3–4 g during acceleration, and 5–6 g when braking from high speeds. During cornering at high speeds, drivers experience lateral forces between 4–6.5 g.[73][74]

A modern F1 car can achieve top speeds of nearly 375 km/h (233 mph), and operate on average speeds of about 200 km/h (120 mph) during a race.[70] Top speeds in practice are achieved in straight parts of a track, and is determined by the aerodynamic configuration of the car in balancing between high straight-line speed (low aerodynamic drag) and high cornering speed (high downforce) to achieve the fastest lap time.[75] In 2005, Mclaren recorded a record top speed of 372.6 km/h (231.5 mph) during testing, which was officially recognised by the FIA as the fastest speed ever achieved by an F1 car. [76] At the 2016 Mexican Grand Prix, the Williams of Valtteri Bottas reached a top speed of 372.54 km/h (231.49 mph) in racing conditions.[77][78] Away from the track, the BAR Honda team used a modified BAR 007 car, to set an unofficial speed record of 413 km/h (257 mph) on a one way straight-line run on 6 November 2005 at Bonneville Speedway and the car set an FIA ratified record of 400 km/h (250 mph) on 21 July 2006 Bonneville.[79]

References

[edit]
  1. ^ a b c d "Evolution of F1 cars". Red Bull Racing. Retrieved 1 June 2024.
  2. ^ a b c "Bodywork rules". F1technical.net. 11 June 2021. Archived from the original on 3 August 2024. Retrieved 1 June 2024.
  3. ^ "2008 Formula One Technical Regulations" (PDF). FIA. Archived (PDF) from the original on 11 May 2008.
  4. ^ "Formula 1 in 2022: Explaining the new rules and car changes as teams prepare for first launches". Sky Sports. Archived from the original on 10 February 2023. Retrieved 10 February 2023.
  5. ^ Morlidge, Matt (4 February 2022). "Formula 1 in 2022: Explaining the new rules and car changes as teams prepare for first launches". Sky Sports. Archived from the original on 10 February 2023. Retrieved 10 February 2023.
  6. ^ "Parts of Formula One car". Fortloc. Archived from the original on 20 July 2024. Retrieved 1 June 2024.
  7. ^ "Technical Regulations – Weight". FIA. Archived from the original on 26 February 2015. Retrieved 21 January 2013.
  8. ^ "Scrutineering and weighing". FIA. Archived from the original on 24 June 2018. Retrieved 24 June 2018.
  9. ^ "F1 vs F2 compared". Motorsport.com. Retrieved 1 June 2024.
  10. ^ "McLaren Racing - History of the F1 engine". McLaren Racing. Archived from the original on 18 March 2023. Retrieved 10 November 2020.
  11. ^ a b c d e "F1 Engine rule change through the years". Formula1 dictionary. Archived from the original on 11 November 2020. Retrieved 10 November 2020.
  12. ^ a b c "Formula 1 Engine". Formula1 dictionary. Archived from the original on 12 November 2020. Retrieved 10 November 2020.
  13. ^ "Villeneuve: A peak of 375 km/h". Auto123. Archived from the original on 22 April 2022. Retrieved 20 January 2022.
  14. ^ "F1 2010 Technical Regulations – Engines and KERS". FIA. Archived from the original on 15 January 2010. Retrieved 23 August 2010.
  15. ^ "Engine / gearbox". Formula1. Archived from the original on 12 April 2012. Retrieved 17 March 2012.
  16. ^ Benson, Andrew (29 June 2011). "Formula 1 bosses confirm engines will not change until 2014". BBC News. Archived from the original on 3 September 2011. Retrieved 17 March 2012.
  17. ^ "Formula 1's 2021 regulations: What's new for 2021?". Autosport. 15 January 2021. Archived from the original on 13 September 2021. Retrieved 13 September 2021.
  18. ^ "Formula 1 unveils 2021 engine plans". Speedcafe. 1 November 2017. Archived from the original on 7 November 2017. Retrieved 8 September 2020.
  19. ^ Jamie Woodhouse (28 February 2022). "All the major changes for the F1 2022 season". PlanetF1. Archived from the original on 7 April 2023. Retrieved 28 February 2023.
  20. ^ "Formula 1 on course to deliver 100% sustainable fuels for 2026". Formula 1. 26 June 2022. Archived from the original on 22 May 2024. Retrieved 1 June 2024.
  21. ^ "Why was refuelling banned in F1? History of refuelling and previous accidents". Motorsport.com. 27 December 2024. Archived from the original on 6 January 2024. Retrieved 1 June 2024.
  22. ^ "Formula 1 fuel systems". Racecar engineering. 7 May 2023. Archived from the original on 15 April 2024. Retrieved 1 June 2024.
  23. ^ "Formula 1 Fuel Tank Safety Explained". F1 Chronicle. 7 August 2024. Archived from the original on 20 June 2024. Retrieved 1 November 2024.
  24. ^ "How Does an F1 Steering Wheel Work?". Mercedes F1. Archived from the original on 23 August 2024. Retrieved 28 October 2024.
  25. ^ "How Does an F1 Steering Wheel Work?". The Drive. 17 June 2021. Archived from the original on 19 September 2024. Retrieved 28 October 2024.
  26. ^ "The $50,000 steering wheels of Formula 1". Jalopnik. 25 March 2011. Archived from the original on 15 December 2012. Retrieved 28 October 2012.
  27. ^ "Forti-Corse – full profile". F1rejects. Archived from the original on 10 October 2007. Retrieved 29 October 2006.
  28. ^ "Future vision: Engineers discuss 2014 changes". Formula 1. Archived from the original on 6 October 2014. Retrieved 20 October 2014.
  29. ^ "F1 2010 Technical Regulations – Transmission system". Formula 1. Archived from the original on 22 July 2010. Retrieved 26 August 2010.
  30. ^ "Understanding the Sport – Engine/Gearbox". Formula 1. Archived from the original on 22 February 2014. Retrieved 24 August 2010.
  31. ^ "Traction control returns; but it's not quite as simple as that". Grandprix.com. Archived from the original on 27 October 2021. Retrieved 4 December 2020.
  32. ^ "What Has F1 Ever Done for Us?". Bleacher Report. Archived from the original on 28 April 2022. Retrieved 5 December 2020.
  33. ^ "F1 Transmission". F1technical.net. 3 October 2003. Archived from the original on 19 January 2022. Retrieved 25 August 2010.
  34. ^ "F1 Engines". F1technical.net. 18 July 2009. Archived from the original on 9 November 2021. Retrieved 25 August 2010.
  35. ^ "Seamless Gearbox". Formula1-dictionary. Archived from the original on 18 May 2022. Retrieved 30 June 2022.
  36. ^ "Managing change: what's new for 2008 – Part Two". Formula 1. 21 February 2008. Archived from the original on 20 April 2009. Retrieved 4 May 2009. Sporting Regulations, Article 28.6
  37. ^ "The beginner's guide to Formula 1 engine and gearbox penalties". Formula 1. 10 February 2023. Archived from the original on 29 May 2024. Retrieved 1 June 2024.
  38. ^ a b c d "Formula 1 tyre evolution". Automobilist. Retrieved 1 June 2024.
  39. ^ "The Evolution of Race Tyres". Stuckey Tyres. Retrieved 17 November 2018.
  40. ^ Ernst, Kurt (12 August 2013). "Montjuic, 1971: When Formula 1 met racing slicks". Hemmings Daily. Archived from the original on 14 December 2019. Retrieved 1 May 2020.
  41. ^ "Ferrari 312T". F1technical.net. Archived from the original on 20 July 2019. Retrieved 1 June 2019.
  42. ^ "Ferrari F1 87-88". F1technical.net. Archived from the original on 17 November 2018. Retrieved 17 November 2018.
  43. ^ "F1 rules and stats 1990–1999". F1technical.net. January 2009. Archived from the original on 6 November 2019. Retrieved 1 June 2019.
  44. ^ De Groote, Steven (3 July 2008). "Tyre use in Formula One". F1technical.net. Archived from the original on 5 November 2020. Retrieved 6 December 2016.
  45. ^ "Formula One – Sporting Regulations – 2007" (PDF). FIA. 13 July 2007. Archived (PDF) from the original on 29 January 2019. Retrieved 11 June 2019.
  46. ^ "Formula One – Technical Regulations – 2008" (PDF). FIA. 12 February 2008. Archived (PDF) from the original on 21 October 2017. Retrieved 11 June 2019.
  47. ^ "Formula One – Technical Regulations – 2009" (PDF). FIA. 11 July 2008. Archived (PDF) from the original on 10 September 2008. Retrieved 21 November 2008.
  48. ^ "Everything you need to know about F1 tyres". Williams F1. Archived from the original on 25 May 2024. Retrieved 1 June 2024.
  49. ^ "Règlements 2010: technique et sportif". ZoneF1 (in French). 2010. Archived from the original on 19 April 2016. Retrieved 1 June 2019.
  50. ^ "Pirelli tyres, adjustable rear wings among 2011 changes". Tata Communications. 23 June 2010. Archived from the original on 21 October 2012. Retrieved 24 June 2010.
  51. ^ "Pirelli tyres to have six different colours for 2011 Formula 1 season". Pirelli. Retrieved 28 March 2011.
  52. ^ "New markings for Pirelli's tyres". Planet F1. Archived from the original on 25 April 2011. Retrieved 28 May 2011.
  53. ^ Parkes, Ian (11 December 2015). "How the 2016 Formula 1 tyre rules will work". Autosport. Archived from the original on 5 June 2016. Retrieved 3 June 2016.
  54. ^ "Tyres". Formula 1. Archived from the original on 29 June 2019. Retrieved 10 March 2019.
  55. ^ "GP2 series to use Pirelli's F1 tyres in 2011". Motorsport.com. Archived from the original on 17 November 2018. Retrieved 17 November 2018.
  56. ^ a b "Formula One breaking explained". Mercedes F1. Archived from the original on 9 February 2024. Retrieved 1 June 2024.
  57. ^ "Break system". F1technical.net. Archived from the original on 6 April 2022. Retrieved 21 July 2007.
  58. ^ a b c d "How a F1 front wing works". F1 blast. 20 March 2024. Archived from the original on 24 June 2024. Retrieved 1 June 2024.
  59. ^ a b c "How a F1 rear wing works". F1 blast. 28 March 2024. Archived from the original on 24 June 2024. Retrieved 1 June 2024.
  60. ^ "How KERS works". Racecar engineering. 29 March 2009. Archived from the original on 4 September 2021. Retrieved 1 June 2024.
  61. ^ "2009 Technical regulations" (PDF). FIA. 22 December 2006. Archived from the original (PDF) on 25 June 2008. Retrieved 8 July 2008.
  62. ^ "Nose Cone design". F1technical.net. September 2013. Archived from the original on 15 May 2024. Retrieved 1 June 2024.
  63. ^ "The FIA approves Formula 1's first supplier to the Halo". F1i.com. 16 January 2018. Archived from the original on 29 March 2018. Retrieved 28 March 2018.
  64. ^ "Air boxes and filters". Racecar engineering. 12 April 2013. Archived from the original on 4 March 2021. Retrieved 1 June 2024.
  65. ^ "Understanding F1 Racing – Aerodynamics". Formula 1. Archived from the original on 26 March 2014. Retrieved 17 July 2007.
  66. ^ "Japanese Grand Prix – team and driver preview quotes". Formula 1. Archived from the original on 28 February 2010. Retrieved 12 October 2012.
  67. ^ "2011 F1 Technical Regulations, Section 3.18" (PDF). FIA. 8 March 2011. Archived (PDF) from the original on 13 March 2012. Retrieved 8 May 2024.
  68. ^ "F1 V6 turbos are more powerful than V8s or V10s says, Mercedes' engine boss". James Allen. 27 November 2015. Archived from the original on 22 November 2020. Retrieved 11 October 2016.
  69. ^ "F1 car specifications". Radio times. Retrieved 1 June 2024.
  70. ^ a b "F1 car top speed". Racing news. Retrieved 1 June 2024.
  71. ^ "Power to weight ratio". Omni. Archived from the original on 22 April 2024. Retrieved 1 June 2024.
  72. ^ F1 2016 V6 Turbo 0–100 kmh Onboard – all manufacturers, 6 October 2016, archived from the original on 18 September 2019, retrieved 11 October 2016
  73. ^ "G-Force". formula1-dictionary.net. Archived from the original on 24 May 2022. Retrieved 12 January 2018.
  74. ^ "How many gs can a f1 car pull". F1 Chronicle. Archived from the original on 26 February 2024. Retrieved 1 June 2024.
  75. ^ "The importance of aerodynamics". F1technical.net. Archived from the original on 18 September 2019. Retrieved 26 January 2007.
  76. ^ "Blink and you'll miss these F1 records". Red Bull. Archived from the original on 23 July 2018. Retrieved 31 October 2016.
  77. ^ "Race Speed Trap". FIA. Archived from the original on 23 April 2022.
  78. ^ "372.54 km/h by Valtteri Bottas in Mexico GP, new F1 speed record according to official statistics (with image, tweet)". Storify. Archived from the original on 23 January 2017. Retrieved 10 March 2017.
  79. ^ "FIA ratify Honda Racing F1 Team's Bonneville records". Bonneville 400. 15 November 2006. Archived from the original on 2 November 2005. Retrieved 24 January 2007.
[edit]
Wikimedia Commons has media related to Formula One car.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Formula_One_car&oldid=1263257259"